Starting to draw
This page presents a simple sequence of creating a basic drawing, from a blank document to a printed design. It assumes that you have installed LibreCAD and have opened it to a new default blank drawing. It introduces quite a few LibreCAD concepts, and links to other pages that explain these.
You can download and unzip File:Carport.zip to compare our results with what the authors of this document saved.
The first part of any design is a freehand sketch on paper. This is quick and simple and so allows for greatest freedom in the design process.
We'd like to create a drawing of the following alumnium structure which sits on top of a carport.
Start a drawing
- Start LibreCAD
- First you might want to decide about your application preferences using Options/Application Preferences/Appearance
- For this example the background color has been changed to "white"
- Save the default "unnamed document 1" as "CarportEast" using the "File/Save" Menu
- Check that the save was successful by Quitting LibreCAD, and restarting it. The saved file "CarportEast.dxf" should show up in the "File/Recent Files" Menu
- Reopen the file and close the "unnamed document 1" by clicking the circled x in the tab.
We'd like to have an A4 drawing on which a scaled version of the 5000 x 1300 mm construction fits.
A4 is 297 x 210 mm so if we make the 5000 mm be shown as a 250 mm long line we'd be set. That is a 1:20 scale.
Via the menu Options/Current Drawing Preferences/Dimensions we can se the General Scale to 20 to achieve the scaling.
The first lines of any technical drawing are the construction lines, setting out the locations of all lines without specifying any line types, colours, etc. All straight construction lines are of 'infinite' length — i.e. they extend off the screen in both directions.
- Create a new Construction layer by clicking the "+" sign in the Layer list. The new layer might have a name such as 'construction', and a colour of magenta or cyan or similar. The line's width should be '0'.
- Make sure Snap on grid is enabled.
We'd like to create a 5000 x 1300 mm construction line drawing box in which our construction will be placed.
- Hit space to enter the command line mode - the cursor will jump to the lower right corner and "Command" will be in blue
- Type polyline or "pl" - you'll now asked for the points
- Specify first point: 0.0
- Specify next point: 5000,0
- Specify next point or [undo]: 5000,1300
- Specify next point or [close/undo]: 0,1300
- Specify next point or [close/undo]: close
Zoom out with the View/AutoZoom menu item You should now see a 5 x 1.3 m rectangle at 1:20 scale
Try printing the page with File/Print - the printout should be empty since the construction layer will not be printed
Drawing the frame
For the frame we would like to create three rectangles that represent the sides of the frame. Each side has 40 mm width, so we simply take the three corner of the triangle:
and shift the coordinates by 40 mm accordingly.
Add three more polylines in the default layer:
Command: pl (polyline) 0,0 5000,0 5000,40 0,40 close 4960,0 4960,1300 5000,1300 5000,0 close 5000,1300 5000,1260 0,0 0,40 close
Should you have made a typing error you might want to use the "undo" command to remove the latest drawing item that didn't go as you intended.
You might want to save your result with File/Save. This time if you print things out with File/Print the result should be visible. You can also check what the print looks like with File/Print Preview which will open up a new tab
You'll find a saved version up to this step in the file CarportEastStep1.dxf in the zip file mentioned above.
Drawing the support beams
The next three polygons are a bit more tricky. We need to find out the positions to use from the dimensions we measured. Fortunately for the math there are helpers on the internet:
- Via https://www.calculator.net/slope-calculator.html (using "If the 2 points are known")
For a triangle to be calculated we need three values.
For the three beams we only have the length and slope 14.57 degress at this time:
- 363 mm
- 845 mm
- 1050 mm
But we can also see that we have two angles available:
- 14.57 degrees derived from the frame triangle
- approx 90 degrees at which the beams are attached on the top side
Since we have three values of the triangle we can calculate the other values with
Triangles for Beams
We'll add this triangle in the construction layer using LibreCads capability to use relative and polar coordinates
- Select the construction layer in the layer list
- press space to enter the command mode
- enter the polygon for the triangle:
pl 0,0 1443,0 @363<104.57 close
The values are from the triangle calculator.
- 0,0 is the start point
- 1443 is the x position at which the 363 mm long beam leave the x axis
- it leaves at an angle of 75.43 which we have to enter anti-clock wise with makes it 104.57 (90 degrees more ...) the new point is to be calculated relatively so we have used the @ symbol to denote this, the < symbol denotes that we are specifing a polar coordinate.
We repeat this for our other beams
0,0 3359,0 @845<104.57 close 0,0 4174,0 @1050<104.57 close
You'll find a saved version up to this step in the file CarportEastStep2.dxf in the zip file mentioned above.